How much mulch do I need?
Area times depth, converted into the units mulch is sold in. The arithmetic is three steps and the calculator will do it for any number of beds — but the measuring is the part that decides whether the answer is right.
The short answer
Multiply the bed's square footage by the depth in inches, divide by 12, then divide by 27. That gives cubic yards. For bags, take the cubic feet figure from the middle step and divide by the bag size — usually 2.
A worked example. A bed 20 feet long and 10 feet wide is 200 square feet. At 3 inches: 200 × 3 ÷ 12 = 50 cubic feet, and 50 ÷ 27 = 1.85 cubic yards. In bags that is 50 ÷ 2 = 25 bags. Add 10% for waste and call it two yards, or 28 bags.
Step 1 — measure the beds
This is where the error comes from, not the arithmetic. A few things that make it easier:
- Feet, not inches. Measure everything in feet and decimals of a foot. Mixing units is the most common mistake in this calculation.
- Pace it if you have no tape. Measure your own pace once against a known length, then count paces. It is accurate to a few percent, which the waste allowance covers.
- Break up irregular beds. A curved border is a rectangle plus a triangle plus a half-circle. Measure each piece and add them — the calculator takes each as a separate bed.
- Subtract what you are not mulching. A tree ring, a pond, a large shrub base. The ring or border shape exists for exactly this.
Step 2 — choose the depth
Depth changes the answer more than any measurement error will: going from 2 inches to 4 doubles the order. It deserves a decision rather than a default.
| Depth | When | Per 100 sq ft |
|---|---|---|
| 2" | Established, densely planted beds; over bulbs | 0.6 cu yd · 9 bags |
| 3" | The general default | 0.9 cu yd · 13 bags |
| 4" | New beds, heavy weed pressure | 1.2 cu yd · 17 bags |
Bag counts are for 2 cubic foot bags, rounded up. The full grid is on the coverage chart.
Step 3 — convert
Two divisions, both exact. Dividing by 12 turns a depth in inches into a depth in feet, which is what makes the multiplication produce cubic feet. Dividing by 27 turns cubic feet into cubic yards, because a cubic yard is a three-foot cube.
Neither number is an approximation, which is why every volume figure on this site is exact arithmetic rather than an estimate. Theconversions page shows the working for all of them.
Step 4 — add for waste, then round up
Add about 10%. Beds settle, ground is not flat, and a bed measured by pacing is a few percent out in one direction or the other. Then round up — to whole bags, or to the nearest half yard for a bulk order, since that is the increment most suppliers will actually load.
Round up rather than to nearest. The cost of a surplus bag is one bag; the cost of being short is a second trip, and possibly a visibly different batch of dyed mulch across the same bed.
If you are topping up rather than starting fresh
Measure what is already in the bed and calculate the difference, not a full layer. Push a finger or a trowel down to soil level in a few places: if there is an inch and a half left and you want three, you are buying an inch and a half, which is half the mulch.
Check the total while you are down there. Mulch accumulating past four inches over several seasons starts working against you, and the fix is to rake some out rather than add more.
Getting it home
Volume decides what you order; weight decides what you can carry. A cubic yard of wood mulch runs roughly 400 to 800 pounds depending on the material and how wet it is, and a half-ton pickup's payload is around 1,000 to 1,500 pounds. One yard is comfortable, two is at the limit, and two wet yards may be past it.
If it is being delivered in bulk, plan the moving too. The calculator reports wheelbarrow loads because a pile on the driveway is a job, not a delivery — roughly nine barrow loads per cubic yard.
Questions
How much mulch do I need for 100 square feet?
At 3 inches deep, 0.9 cubic yards — call it one yard, or 13 bags at 2 cubic feet. At 2 inches it is 0.6 yards, and at 4 inches, 1.2 yards. Depth changes the answer proportionally, so it is the number worth getting right.
How do I measure my yard for mulch?
Take each bed separately rather than the yard as a whole. Measure its length and width in feet for a rectangle, or the radius for a circle, and note the depth you want in inches. Add the beds together at the end. A tape measure is ideal, but pacing the edges is usually close enough — a normal stride is about 2.5 feet, and mulch is sold in whole bags and half yards, so a few inches either way rarely changes what you buy.
How do I measure an irregular bed?
Break it into shapes you can measure — a rectangle plus a triangle plus a half-circle — and add them. The calculator takes each as a separate bed and totals them for you. For a genuinely freeform bed, pace the longest length and the average width and treat it as a rectangle; the waste allowance absorbs the error.
Should I round up or down?
Up, always. A surplus bag gets used somewhere; running out three-quarters of the way through means a second trip and possibly a different dye lot. The calculator adds 10% by default for exactly this reason, and rounds bags up rather than to nearest.
Do I need to remove the old mulch first?
Usually not. Wood mulch decomposes into the soil, so topping up is normal practice. Remove it if it has matted into a water-shedding crust, if it has grown a fungal mat, or if the total depth is creeping past four inches — measure what is already there and top up to your target rather than adding a full layer on top.
How much mulch fits in a pickup truck?
By volume, a standard short bed holds about 2 cubic yards level with the sides and a long bed around 2.5. By weight you will hit the limit first: a half-ton truck's payload is roughly 1,000 to 1,500 lb, which is one to two yards of wood mulch, less if it is wet.